LOAD CELL - INSTRUMENTS

                  DIN RAIL MOUNT-CE APPROVED-PC SYSTEMS 

NEW DAD143.1 Profinet. Ethernet/IP, EtherCAT, Modbus

  Veje instrumenter  

High quality load excitation module. 

The Digital Amplifier, DAD141.1 is an all-in-one device for non-automatic and automatic weighing, filling or loss-in-weigh operations. The standard device includes all the communication facilities needed for industrial weighing, control and registration, i.e. analog current- and voltage output, Ethernet, RS485 and logic I/O’s for direct control of valves or bars and simple remote operations.

DAD141.1 is a stand-alone device for DIN-rail mounting (TS35).An App for Android enables set-up and calibration of the DAD141.1 via most smart phones and tablets.

To grant the quality and allow legal weighing the DAD141.1 is OIML R-76 approved and tested to meet the MID requirements to EMC at industrial surroundings.   

NEW option for DAD141.1  

Small PC board UIA149.1 make it now possible via the 7 load cell terminals to connect other type of sensors with Volt or 4-20mA input and still use all the nice facilities which are in the DAD141.1 also the DOP Free PC software.

       NEW DAD14X.X  Models         

         DAD141.3: RS422/485 2/3 I/O's (No Analog out) 

DAD142.2: Profibus DP-V0   

DAD143.1: 2 ETHERNET with support for Profinet, Ethernet/Ip, Ethernet-CAT & Modbus TCP, +analog out put = Volt / mA     

DAD143.2 Same as 143.1 but NO analog output on this.

DOP free Download PC software to be used with DAD141.1 can also be used as Calibration of the DAD141.1

NOW ALSO IN PROFIBUS or Profinet  VERSION DAD143.1

 

 

DATA  DAD143.1

Performance Linearity <0.001% of full scale.

Load cell excitation voltage 5 Vdc

Load cell drive capability RLC 58-2000 Ω (≤6 pc 350 Ω load cells)

Load cell wiring system 6 wires inclusive sense

Load cell input range ±3.3 mV/V equivalent to ±16,5 mVdc.

Load cell input resolution ≈50 nV/incr. (≈200 000 counts at 2 mV/V input)

A/D-conversion rate 600 updates/second

Fix LP filter, default 20 Hz; 60 db/decade ( can be sat to 0 for PEAK )

Adjustable digital IIR LP filter 18-0.25Hz; 40db/decade, selectable in 8 steps

Adjustable digital FIR LP filter 19.7-2.5Hz, selectable in 8 steps

Output update rate 600-0.6 updates/second, selectable in 8 steps

Display averaging rate 5 updates/second

General I/O’s Hardware interfaces RS485, drives 32 nodes or RS422 –full duplex

Data transmission, rates, RS485 9.6; 19.2; 38.4; 57.6; 115.2 kB

Data transmission, protocol Get results or auto transmit

Ethernet TCP/IP Modbus and other protocols available. 

Isolated Analogue current output 0-20mA or 4-20mA. 500ohm.

 Isolated Analogue voltage output 0-10V; 0-5V; ±5V; ±10V. 10kohm.

 Isolated Logic inputs 2 (10-30 V; 1-3 mA)  Isolated. Logic outputs 3 FET’s (30 Vac; 0.5 A) Separate grnd.;

Isolated. Internal calibration reference 2,000.0mV/V

Power supply 10-30Vdc ≤15% ripple; ≤4Watt. Isolated.

Facilities Display, optical spectral filtered 6 digit, 7seg. Green LED’s, 5.08mm.

Indicators 8 green LEDs.

Keyboard 4 pc Ø3mm robust, short travel push buttons

Sealing for legal operations (Green M) Plug and key-board lid to be sealed with labels.

DFI-2  MINI LOAD CELL INDICATOR

Now with USB-2 connection & Data logger option with AEP PC software

 GR5 DYNAMOMETER

EXCITATION ANALOG OUTPUT

EXCITATION TO DIGITAL COMMUNICATION

USB TO PC

 BENDING CELLS

 PLATFORM  CELLS

COMPRESSION CELLS

 TENSION CELLS

VEJEINSTRUMENTER

FARVEKODER NTT VEJECELLER 

DIGITALE & ANALOGE VEJEINSTRUMENTER FRA H&B

small size 16mm tube analogue excitation unit for 2 wire 4..20mA signal output.

SMART WEIGHING          .... SOLUTIONS

OIML R76 Approved  weighing instruments, high Quality instruments with many models and options for numberless weighing jobs.  

NTLB DIN rail series of modern load cell excitation units which can be supplied either with analogue output as: 0-20mA,4-20mA, 0-10V, 0-5V, +/-10V,+/-5V.

Standard with 3 set points and RS485 communication.

Can drive 8  x 350 Ohm load cells.

NTLB Analogue - DATA 

NTLB4  4 Load cells input - DATA    

12 different possible communication forms !

Weight transmitter with 4 independent reading channels with

display of the total weight

The TLB4 series allows to have same benefits and performance of an advanced digital weighing system even using analog load

cells.

Back panel mounting on Omega/DIN rail or front panel with fixing kit included (panel drilling template 23x96 mm; panel thickness 2.5 mm).

Dimensions: 26x115x120 mm.

Six-digit red LED semi alphanumeric display (8 mm height), 7segment.

Six indicator LED.

Four buttons for the system calibration.

Extractable screw terminal

 

 

LAUMAS ELECTRONIC

     NTLB4 

Panel mounting of front protection part.

RS485 serial port for communication via Modbus RTU protocol,

ASCII bidirectional or continuous one way transmission.

3 relay logic outputs controlled by the setpoint values or via protocols.

2 opto-isolated PNP logic inputs: 

status reading via serial communication protocol.

4 load cell dedicated inputs.

TLM8 Advanced Weight Transmitter with 8 Independent  Reading Channels Analog output with RS485 or 10 different standard communication protocols !!    ++++ a lot more                                 

LAUMAS ELECTRONIC

NTLS Digital-Analog transmitter with RS485

NTLU Digital-Analog transmitter Suitable for lifting systems

Load cells connections continuous check

3 alarm thresholds normally closed and 1 SPDT contact 

( Single Pole Double Thro)

Call us for detailed data on this product at:  ntt@ntt.dk 

CAJAN Load cell Junction boxes in solid PVC or Aluminum 

More products on next page

  LOAD CELLS